View B133EW03-V1_7871359.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1 of 32 au optronics corporation product specification auo nbbu spec. template-led 1.0 ( ) preliminary specifications ( v ) final specifications module 13.3 wxga color tft-lcd model name b133ew03 v1 note ( ) led backlight without driving circuit design customer date checked & approved by date note: this specification is subject to change without notice. approved by date howard lee 11/07/2008 prepared by wei hsiang lo 11/07/2008 nbbu marketing division / au optronics corporation pdf created with pdffactory trial version www.pdffactory.com www..net
2 of 32 au optronics corporation product specification auo nbbu spec. template-led 1.0 contents 1. handling precautions...............................................................4 2. general description.................................................................5 2.1 general specification......................................................................................................................5 2.2 optical characteristics....................................................................................................................6 3. functional block diagram......................................................11 4. absolute maximum ratings....................................................12 4.1 absolute ratings of tft lcd module..........................................................................................12 4.2 absolute ratings of environment..................................................................................................12 5. electrical characteristics........................................................13 5.1 tft lcd module.........................................................................................................................13 5.2 backlight unit...............................................................................................................................15 6. signal characteristic..............................................................16 6.1 pixel format image.......................................................................................................................16 6.2 the input data format....................................................................................................................17 6.3 signal description/pin assignment................................................................................................18 6.4 interface timing............................................................................................................................21 7. connector description...........................................................24 7.1 tft lcd module.........................................................................................................................24 8. led driving specification.......................................................25 8.1 connector description..................................................................................................................25 8.2 pin assignment.............................................................................................................................25 9. vibration and shock test.......................................................26 9.1 vibration test...............................................................................................................................26 9.2 shock test spec:..........................................................................................................................26 10. reliability............................................................................27 11. mechanical characteristics...................................................28 11.1 lcm outline dimension.............................................................................................................28 12. shipping and package..........................................................30 12.1 shipping label format................................................................................................................30 12.2 carton package...........................................................................................................................31 11.3 shipping package of palletizing sequence....................................................................................32 pdf created with pdffactory trial version www.pdffactory.com www..net
3 of 32 au optronics corporation product specification auo nbbu spec. template-led 1.0 record of revision version and date page old description new description remark 0.1 2008/04/28 all first edition for customer 1.0 11/07/2008 all final edition for customer pdf created with pdffactory trial version www.pdffactory.com www..net
4 of 32 au optronics corporation product specification auo nbbu spec. template-led 1.0 1. handling precautions 1) since front polarizer is easily damaged, pay attention not to scratch it. 2) be sure to turn off power supply when inserting or disconnecting from input connector. 3) wipe off water drop immediately. long contact with water may cause discoloration or spots. 4) when the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) since cmos lsi is used in this module, take care of static electricity and insure human earth when handling. 7) do not open nor modify the module assembly. 8) do not press the reflector sheet at the back of the module to any directions. 9) at the insertion or removal of the signal interface connector, be sure not to rotate nor tilt the interface connector of the tft module. 11)after installation of the tft module into an enclosure (notebook pc bezel, for example), do not twist nor bend the tft module even momentary. at designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the tft module from outside. otherwise the tft module may be damaged. 12) small amount of materials having no flammability grade is used in the lcd module. the lcd module should be supplied by power complied with requirements of limited power source (iec60950 or ul1950), or be applied exemption. 13) disconnecting power supply before handling lcd modules, it can prevent electric shock, do not touch the electrode parts, cables, connectors and led circuit part of tft module that a led light bar build in as a light source of back light unit. it can prevent electrostic breakdown. pdf created with pdffactory trial version www.pdffactory.com www..net
5 of 32 au optronics corporation product specification auo nbbu spec. template-led 1.0 2. general description b133ew03 v1 is a color active matrix liquid crystal display composed of a tft lcd panel, a driver circuit, and led backlight system. the screen format is intended to support the wxga (1280(h) x 800(v)) screen and 262k colors (rgb 6-bits data driver) with led backlight driving circuit. all input signals are lvds interface compatible. b133ew03 v1 is designed for a display unit of notebook style personal computer and industrial machine. 2.1 general specification the following items are characteristics summary on the table at 25 condition: items unit specifications screen diagonal [mm] 337.8 (13.3w ) active area [mm] 286.08 x 178.8 pixels h x v 1280x3(rgb) x 800 pixel pitch [mm] 0.2235x0.2235 pixel format r.g.b. vertical stripe display mode normally white white luminance (i led =16ma) (note: iled is led current) [cd/m 2 ] 280 typ. (5 points average) 250 min. (5 points average) luminance uniformity 1.25 max. (5 points) contrast ratio 500 typ , response time [ms] 20 typ / 25 max nominal input voltage vdd [volt] +3.3 typ. power consumption [watt] 4.2 typ. (include logic and blu power) weight [grams] 219 max. l w t max C C 3.045 typ 297.15 203.15 2.86 physical size [mm] min C C C electrical interface 1 channel lvds surface treatment glare, hardness 3h, reflection ~0.5% support color 262k colors ( rgb 6-bit ) pdf created with pdffactory trial version www.pdffactory.com www..net
6 of 32 au optronics corporation product specification auo nbbu spec. template-led 1.0 temperature range operating storage (non - operating) [ o c] [ o c] 0 to +50 - 2 5 to +6 5 rohs compliance rohs compliance 2.2 optical characteristics the optical characteristics are measured under stable conditions at 25 (room temperature) : item unit conditions min. typ. max. note white luminance (i led =16ma) [cd/m 2 ] 5 points average 250 280 - 1, 4, 5. [degree] [degree] horizontal (right) cr = 10 (left) - - 75 75 - - viewing angle [degree] [degree] vertical (upper) cr = 10 (lower) - - 60 60 - - 4, 9 luminance uniformity 5 points - - 1.25 1, 3, 4 luminance uniformity 13 points - - 1.50 2, 3, 4 cr: contrast ratio dcr:off 300 500 - 4, 6 cross talk % 4 4, 7 [msec] rising - - - [msec] falling - - - response time [msec] rising + falling - 20 25 4, 8 red x 0.575 0.600 0.625 red y 0.325 0.345 0.365 green x 0.300 0.320 0.340 green y 0.530 0.555 0.580 blue x 0.130 0.150 0.170 blue y 0.100 0.120 0.130 white x 0.263 0.313 0.363 chromaticity of color coordinates (cie 1931) white y 0.279 0.329 0.379 4, 9 pdf created with pdffactory trial version www.pdffactory.com www..net
7 of 32 au optronics corporation product specification auo nbbu spec. template-led 1.0 note 1 : 5 points position (ref: active area) 1 2 3 4 5 h/4 h/4 h/4 h/4 h w w/4 w/4 w/4 w/4 note 2 : 13 points position (ref: active area) w/4 w w/4 h h/4 h/4 h/4 h/4 7 9 10 w/4 1 8 w/4 10 10 10 10 2 3 13 12 4 5 6 11 note 3 : the luminance uniformity of 5 or13 points is defined by dividing the maximum luminance values by the minimum test point luminance note 4 : measurement method the lcd module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change during measuring. in order to stabilize the luminance, the measurement should be executed after w13 = maximum brightness of thirteen points minim um brightness of thirteen points maximum brightness of five points w5 = minimum brightness of five points pdf created with pdffactory trial version www.pdffactory.com www..net
8 of 32 au optronics corporation product specification auo nbbu spec. template-led 1.0 lighting backlight for 30 minutes in a stable, windless and dark room. note 5 definition of average luminance of white (y l ): measure the luminance of gray level 63 at 5 points y l = [l (1)+ l (2)+ l (3)+ l (4)+ l (5)] / 5 l (x) is corresponding to the luminance of the point x at figure in note (1). note 6 definition of contrast ratio: contrast ratio is calculated with the following formula. note 7 definition of cross talk (ct) ct = | y b C y a | / y a 100 (%) where y a = luminance of measured location without gray level 0 pattern (cd/m 2 ) y b = luminance of measured location with gray level 0 pattern (cd/m 2 ) center of the screen tft - lcd 50 cm photo detector lcd panel field=2 contrast ratio (cr)= brightness on the white state brightness on the black state pdf created with pdffactory trial version www.pdffactory.com www..net
9 of 32 au optronics corporation product specification auo nbbu spec. template-led 1.0 note 8 : definition of response time: the output signals of bm-7 or equivalent are measured when the input signals are changed from black to white (falling time) and from white to black (rising time), respectively. the response time interval between the 10% and 90% of amplitudes. refer to figure as below. signal(relative value) "black" tr tf "white" "white" 0% 10% 90% 100% pdf created with pdffactory trial version www.pdffactory.com www..net
10 of 32 au optronics corporation product specification auo nbbu spec. template-led 1.0 note 9 . definition of viewing angle viewing angle is the measurement of contrast ratio R 10, at the screen center, over a 180 horizontal and 180 vertical range (off-normal viewing angles). the 180 viewing angle range is broken down as follows; 90 ( ) horizontal left and right and 90 ( ) vertical, high (up) and low (down). the measurement direction is typically perpendicular to the display surface with the screen rotated about its center to develop the desired measurement viewing angle. pdf created with pdffactory trial version www.pdffactory.com www..net
11 of 32 au optronics corporation product specification auo nbbu spec. template-led 1.0 3. functional block diagram the following diagram shows the functional block of the 13.3 inches wide color tft/lcd module: y - d r i v e r pdf created with pdffactory trial version www.pdffactory.com www..net
12 of 32 au optronics corporation product specification auo nbbu spec. template-led 1.0 4. absolute maximum ratings an absolute maximum rating of the module is as following: 4.1 absolute ratings of tft lcd module item symbol min max unit conditions logic/lcd drive vin -0.3 +4.0 [volt] note 1,2 4.2 absolute ratings of environment item symbol min max unit conditions operating temperature top 0 +50 [ o c] note 4 operation humidity hop 10 90 [%rh] note 4 storage temperature tst -25 +65 [ o c] note 4 storage humidity hst 10 90 [%rh] note 4 note 1: at ta (25 ) note 2: permanent damage to the device may occur if exceed maximum values note 3: led specification refer to section 5.2 note 4: for quality performance, please refer to auo iis (incoming inspection standard) . twb=39 c operating range storage range pdf created with pdffactory trial version www.pdffactory.com www..net
13 of 32 au optronics corporation product specification auo nbbu spec. template-led 1.0 5. electrical characteristics 5.1 tft lcd module 5.1.1 power specification input power specifications are as follows; symble parameter min typ max units note vdd logic/lcd drive voltage 3.0 3.3 3.6 [volt] pdd vdd power - - 0.90 [watt] note 1/2 idd idd current - 220 250 [ma] note 1/2 i rush inrush current - - 1500 [ma] note 3 vddrp allowable logic/lcd drive ripple voltage - - 100 [mv] p-p note 1 : maximum measurement condition black pattern note 2 typical measurement condition: mosaic pattern note 3 measure condition +5.0v +12.0v vcc r1 47k r2 1k vr1 47k sw1 sw mag-spst 1 2 f1 q3 ao6402 g d2 s d1 d5 d6 c1 1uf/16v q3 ao6402 g d2 s d1 d5 d6 c3 0.01uf/25v c2 1uf/25v (high to low) control signal (lcd module input) 90% 10% vin rising time 0v 3.3v 0.5ms pdf created with pdffactory trial version www.pdffactory.com www..net
14 of 32 au optronics corporation product specification auo nbbu spec. template-led 1.0 5.1.2 signal electrical characteristics input signals shall be low or high-impedance state when vdd is off. it is recommended to refer the specifications of thc63lvdf84a (thine electronics inc.) in detail. signal electrical characteristics are as follows; parameter condition min max unit vth differential input high threshold (vcm=+1.2v) - 100 [mv] vtl differential input low threshold (vcm=+1.2v) -100 - [mv] vcm differential input common mode voltage 1.125 1.375 [v] note: lvds signal waveform v t h vcm vss pdf created with pdffactory trial version www.pdffactory.com www..net
15 of 32 au optronics corporation product specification auo nbbu spec. template-led 1.0 5.2 backlight unit led parameter guideline for led driving selection parameter symbol min typ max units condition led forward voltage v f 3.0 3.2 3.3 [volt] (ta=25 ) led forward current i f 16 30 [ma] (ta=25 ) led power consumption p led 2.76 [watt] (ta=25 ) note 1 led life-time n/a 10,000 - - hour (ta=25 ) i f =16 ma n ote 2 note 1: calculator value for reference p led =i f v f led(qty) note 2: the led life-time define as the estimated time to 50% degradation of initial luminous. pdf created with pdffactory trial version www.pdffactory.com www..net
16 of 32 au optronics corporation product specification auo nbbu spec. template-led 1.0 6. signal characteristic 6.1 pixel format image following figure shows the relationship of the input signals and lcd pixel format. r g b r g b r g b r g b r g b r g b r g b r g b 0 1 1278 1279 1st line 800th line pdf created with pdffactory trial version www.pdffactory.com www..net
17 of 32 au optronics corporation product specification auo nbbu spec. template-led 1.0 6.2 the input data format signal name description r5 r4 r3 r2 r1 r0 red data 5 (msb) red data 4 red data 3 red data 2 red data 1 red data 0 (lsb) red-pixel data red-pixel data each red pixel's brightness data consists of these 6 bits pixel data. g5 g4 g3 g2 g1 g0 green data 5 (msb) green data 4 green data 3 green data 2 green data 1 green data 0 (lsb) green-pixel data green-pixel data each green pixel's brightness data consists of these 6 bits pixel data. b5 b4 b3 b2 b1 b0 blue data 5 (msb) blue data 4 blue data 3 blue data 2 blue data 1 blue data 0 (lsb) blue-pixel data blue-pixel data each blue pixel's brightness data consists of these 6 bits pixel data. rxclkin data clock the typical frequency is 68.9 mhz.. the signal is used to strobe the pixel data and de signals. all pixel data shall be valid at the falling edge when the de signal is high. de display timing this signal is strobed at the falling edge of rxclkin. when the signal is high, the pixel data shall be valid to be displayed. vs vertical sync the signal is synchronized to rxclkin . hs horizontal sync the signal is synchronized to rxclkin . note: output signals from any system shall be low or high-impedance state when vdd is off. pdf created with pdffactory trial version www.pdffactory.com www..net
18 of 32 au optronics corporation product specification auo nbbu spec. template-led 1.0 6.3 integration interface and pin assignment lvds is a differential signal technology for lcd interface and high speed data transfer device. pdf created with pdffactory trial version www.pdffactory.com www..net
19 of 32 au optronics corporation product specification auo nbbu spec. template-led 1.0 note1: start from right side 1 30 gnd nc connector pdf created with pdffactory trial version www.pdffactory.com www..net
20 of 32 au optronics corporation product specification auo nbbu spec. template-led 1.0 note2: input signals shall be low or high-impedance state when vdd is off. internal circuit of lvds inputs are as following. the module uses a 100ohm resistor between positive and negative data lines of each receiver input r r r r lvds receiver signal input pin no. 9 11 12 14 15 17 18 8 rxin0+ rxin0- rxin1+ rxin1- rxin2+ rxin2- rxclkin+ rxclkin- pdf created with pdffactory trial version www.pdffactory.com www..net
21 of 32 au optronics corporation product specification auo nbbu spec. template-led 1.0 6.4 interface timing 6.4.1 timing characteristics basically, interface timings should match the 1280x800 /60hz manufacturing guide line timing. note : de mode only pdf created with pdffactory trial version www.pdffactory.com www..net
22 of 32 au optronics corporation product specification auo nbbu spec. template-led 1.0 6.4.2 timing diagram dotclk de t h t hb t hd de t v t vb t vd input timing definition ( de mode) t clock input data pixel 1 pixel 2 pixel 3 pixel n-1 pixel n invaild data invaild data pixel 1 pdf created with pdffactory trial version www.pdffactory.com www..net
23 of 32 au optronics corporation product specification auo nbbu spec. template-led 1.0 6.5 power on/off sequence led on/off sequence is as follows. interface signals are also shown in the chart. power sequence timing value parameter min. typ. max. units t1 0.15 - 10 ms t2 0 20 50 ms t3 200 250 - ms t4 200 250 - ms t5 0 20 50 ms t6 - - 5 ms t7 500 - - ms note: the duty of led dimming signal should be more than 20% in t2 and t3. t7 t 5 t2 t3 valid data t1 10% 90% 10% 90% t4 t 6 power supply vdd lvds interface backlight on pdf created with pdffactory trial version www.pdffactory.com www..net
24 of 32 au optronics corporation product specification auo nbbu spec. template-led 1.0 7. connector description physical interface is described as for the connector on module. these connectors are capable of accommodating the following signals and will be following components. 7.1 tft lcd module connector name / designation for signal connector manufacturer ipex type / part number ipex 20347-330e-12 mating housing/part number ipex 20345-030t-31 pdf created with pdffactory trial version www.pdffactory.com www..net
25 of 32 au optronics corporation product specification auo nbbu spec. template-led 1.0 8. led specification 8.1 general information led manufacturer nichia led manufacture assembly p/n nnsw108-s1 number of leds 54 led bin a6255, a6256, a6257, a6258, a6265, a6266, a6267, a6268, bj255, bj256, bj257, bj258, bj265, bj266, bj267, bj268 led ranks 1800 mcd ~ 2400 mcd led brightness bin 50 mcd per bin led vf 0.2v per bin led forward voltage range for all 6 led series lines max: 30.6 v 8.2 led connection string led 1 led 2 led 3 led 4 led 5 led 6 led 7 led 8 led 9 1 1 7 13 19 25 31 37 43 49 2 2 8 14 20 26 32 38 44 50 3 3 9 15 21 27 33 39 45 51 4 4 10 16 22 28 34 40 46 52 5 5 11 17 23 29 35 41 47 53 6 6 12 18 24 30 36 42 48 54 pdf created with pdffactory trial version www.pdffactory.com www..net
26 of 32 au optronics corporation product specification auo nbbu spec. template-led 1.0 9. vibration and shock test 9.1 vibration test test spec: l test method: non-operation l acceleration: 3.0 g l frequency: 5 - 150hz random l sweep: 30 minutes each axis (x, y, z) 9.2 shock test spec: test spec: l test method: non-operation l acceleration: 200 g , half sine wave l active time: 2 ms l pulse: x,y,z .one time for each side pdf created with pdffactory trial version www.pdffactory.com www..net
27 of 32 au optronics corporation product specification auo nbbu spec. template-led 1.0 10. reliability items required condition note temperature humidity bias ta= 50 , 90%rh, 240h high temperature operation ta= 50 , rh, 300h low temperature operation ta= 0 , rh, 300h high temperature storage ta= 65 , rh, 500h low temperature storage ta= -25 , rh, 500h thermal shock test ta=-20 to 60 , duration at 30 min, 100 cycles esd contact : 8 kv air : 15 kv note 1 note1: according to en 61000-4-2 , esd class b: some performance degradation allowed. no data lost . self-recoverable. no hardware failures. remark: mtbf (excluding the led): 30,000 hours with a confidence level 90% pdf created with pdffactory trial version www.pdffactory.com www..net
28 of 32 au optronics corporation product specification auo nbbu spec. templa te - led 1.0 11. mechanical characteristics 11.1 lcm outline dimension pdf created with pdffactory trial version www.pdffactory.com www..net
29 of 32 au optronics corporation product specification auo nbbu spec. templa te - led 1.0 pdf created with pdffactory trial version www.pdffactory.com www..net
30 of 32 au optronics corporation product specification auo nbbu spec. templa te - led 1.0 12. shipping and package 12.1 shipping label format pdf created with pdffactory trial version www.pdffactory.com www..net
31 of 32 au optronics corporation product specification auo nbbu spec. templa te - led 1.0 12.2 carton package the outside dimension of carton is 435 (l)mm x 377 (w)mm x 335 (h)mm pdf created with pdffactory trial version www.pdffactory.com www..net
32 of 32 au optronics corporation product specification auo nbbu spec. templa te - led 1.0 11.3 shipping package of palletizing sequence pdf created with pdffactory trial version www.pdffactory.com www..net

▲Up To Search▲

Price & Availability of B133EW03-V1

	To Download B133EW03-V1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .